ACCESSORIES AND OPTIONS:

MITERED TIE-POLE

Used to secure poles to a wall. Mitered tie-poles are available in any specified length. AB-0202 brackets are used for pole-to-pole connections. AB-PC or AB-PL brackets provide an attractive connection back to the wall.

Note: if shelves do not touch the wall, additional bracing may be required to prevent side-to-side racking.

TIE-BRACKET

Used to secure any Rakks pole to a wall. Tie-brackets have a PVC flange at the end that is screwed to the wall. One tie-bracket should be located at the top of the pole. Additional tie-brackets can be added for greater stability.

Note: tie-brackets must be specified so that shelves touch the wall.

THREADED INSERT

Used to create a threaded channel in any pole. Facilitates the installation of cabinets or other components using 1/4-20 screws. Secures into pole channel with set-screws.

SPRING COMPRESSION KIT

Used with PL poles for installation between the floor and ceiling. 1-1/8" x 1-5/8" x 11-1/2" rectangular tube slides over pole. Spring and spacers allow for up to 4" overall adjustment. Rubber top and bottom pads protect ceiling and floor. Note: poles should be cut 3î shorter than the finished floor-to-ceiling height.

SPLINE CONNECTOR

Used to connect sections of poles when floor to ceiling heights exceed inventoried lengths. Splines slide into pole channels and are secured using four 10-32 set screws. Two splines are required for each connection.

THREADED MOUNTS

Install into inserts at the top and bottom of PC2, PC4 and PD6 poles for installation between floor and ceiling. These non-skid, non-marking mounts allow for up to 2" overall adjustment.

Note: poles should be cut 3" shorter than the finished floor-to-ceiling height.

ANCHOR BRACKETS

One leg of these L-shaped brackets slides into the pole channel and is secured with 1/4-20 set screws. The other leg can be used to anchor poles to the floor, ceiling or wall. Use two AB-0035 brackets for pole-to-ceiling connections. AB-0202 brackets can be used to make 90-degree pole-to-pole connections.

GROMMETS

Facilitate installation of PS4 and PD6 poles in through-counter installations. These machined Delrin inserts are epoxied into round holes cut into counter tops. Eliminates need to cut square or rectangular holes.

PANEL FRAMING CHANNELS

Used with Rakks poles to support and frame 1/4" decorative panels. Framing channels are manufactured to order to fit any panel width up to 4'. They lock securely into the pole and are held in place by channel nut plates. Available in Clear, Black and White.

CHANNEL NUT PLATES

Used for mounting light fixture, power strips, panels or other items to poles. NP-0832 nut plate can be easily installed or removed from the front of the pole. NP-0420 nut plate must slide into the end of the pole or into an access slot and should be used where a more secure attachment is required.

CHANNEL COVERS

PVC extrusion snaps into pole channels to cover opening for improved sanitation and cleaning. Available in 8' lengths in Translucent and Black PVC.

POLE CORNER ADAPTER

This adapter screws into the side of the PL Series pole and accepts a shelf bracket. It should be used only in corner conditions.

LAMP BRACKET

Accepts drafting lamps with 1/2" diameter bottom shaft. Available in black or clear anodized aluminum.

J-BOLT-ON BRACKET & J-OFFSET BRACKET

Used to attach J-hangbar to poles. The bolt-on bracket screws to the side of PL or PC2 poles. The offset bracket locks into the front or back channel and provides a 1-3/8" offset. Available in left, right andcenter configurations.
More about our Hangbars.

DOOR HINGES

Pole mounted door hinges can accommodate 1/4" glass and 3/4" wood doors up to 18" wide. Hinges can be configured for single or double door applications. Available in polished aluminum only.